Straight slot bar of 1 inch tubular stainless steel to be added to a brake bar frame to create a descent rack.
Weight: 2.8 oz (80 g)
Length: 2.45" (6.2 cm)
Width: 1.00" (2.5 cm)
Height: 1.00" (2.5 cm)
Material: Stainless Steel
This SMC 1.2-inch single pulley is the mini of minis. Efficient and lightweight, its solid strength and efficiency tests to greater strengths than other pulleys in the same size and price range.
It has the required prusik minding capability for use in a haul system. A 1.20 in nylon sheave and zinc-coated axle make any system run smoothly.Simple to use and easy to carry into the field. Max Rope diameter for the CR is 13 mm. The CR pulley is a single pulley.
Simple to use and easy to carry into the field; max rope diameter for the CR is 13 mm.
The JR and JRB pulleys are double pulleys with a max rope diameter for of 9 mm.
The TR Pulley is strong, reliable compact, and lightweight. It is reasonably priced but doesn't sacrifice efficiency. Great performance for its size and cost. The TR Pulley has a true Oilite Bearing on a zinc coated axle for reliable performance.
Large D shape for great handling, huge gate opening and massive strength. At a rated strength of 72kN, it's one of the strongest carabiners in the world!
Heat-treated, half-load tested (over 8000 lbf.) and built to exacting standards, the Large D is one very fine steel carabiner.
|Part #||Description||Gate Opening
mm / inch
grams / ounces
mm / inch
mm / inch
|OP12S58LNFPA||1/2" Std. D NFPA Screw-Lok||27 / 1.06||72kN||22kN||12kN||283 / 10.0||124.5 / 4.90||70.6 / 2.78|
Noting the unique requirements found in Swift Water Rescue, we created an entirely new pulley to address those needs. The Swiftwater Rescue Pulley represents a reasonably priced, non-NFPA alternative to other midsized pulleys.
Made using high quality aluminum, this lightweight pulley weighs 6 oz. and features a 2‰۪‰۪ sheave. Anodized side plates feature a series of holes that help to minimize the hydroplaning effect that might occur with a typical pulley. These side plates are also configured to work as a Prusik Minding Pulley and are precisely tensioned for easy one-handed operation and secure placement at any point along the rope.
High quality sealed ball bearings help to provide the optimal efficiency that is so crucial in rope rescue systems. They help to reduce the performance-robbing resistance that is inherent in most multiple component systems and are not prone to failure under misaligned loads or with twisted gear that may occur with needle bearings.
The wide and flat base maximizes the effectiveness of a Prusik hitch while a unique side plate formation allows the use of larger ropes in a compact pulley. The top hole accepts 2 large rescue carabiners or multiple small carabiners and allows the carabiners to be rotated freely and completely even while closed.
The unique shape of SMC's aluminum side plates allows the efficient use of prusik hitches as a belay or progress capture device. Constructed with a 3-inch diameter sheave running on a high-efficiency ball bearing. Low profile fasteners help eliminate the possibility of the pulley snagging. Pulley will accommodate up to 13 mm rope.
The unique shape of SMC's aluminum side plates allow the efficient use of prusik hitches as a belay or progress capture device. Constructed with a 3-inch diameter sheave running on a high-efficiency ball bearing. Low profile fasteners help eliminate the possibility of the pulley snagging. Pulley will accommodate up to 13 mm rope.
Angled slot brake bars formed in a "U" shape. Stainless steel bars will not leave aluminum streaks on your rope and will last longer than aluminum bars.
Angled slot brake bars formed in a "U" shape. Stainless steel bars will not leave aluminum streaks on your rope and will last longer than aluminum bars. This model comes with a training groove to ensure appropriate loading.
Type #304 stainless steel construction, with a welded eye for extra strength. Each eye weld is inspected for dye penetration before shipping. Average tensile of material used is over 10,000 lbf.
Developed specifically to meet the needs of rescue system belays. The well-engineered Traverse 540 is a patented, self-locking, easy-to-rig device that meets demanding drop-test criteria: able to hold falling loads quickly while limiting the peak force.
The symmetrical design reduces the risk of improper rigging. A built-in release lever discharges the tension on the belay rope, eliminating the need for a release hitch.
The 540 belay device passes the BCCTR Rescue Belay Competence Drop Test Criteria
** The British Columbia Council of Technical Rescue Belay Competency Drop Test specifies a 1-meter drop onto 3 meters of kernmantle rescue rope with less than 1 meter of additional travel and less than 15 kN peak force. For a General Use rated device, a 280-kg load and a 12.5-mm rope are generally used. For a Technical Use device, a 200-kg load and an 11.1-mm rope are used.
Solid aluminum gives these bars maximum friction and good wear characteristics. Lighter than the stainless bars and available in a straight slot configuration. 7/8" diameter models fit all SMC racks.
Solid aluminum gives these bars maximum friction and good wear characteristics. Lighter than the stainless bars and available in a straight slot configuration. 7/8" diameter models fit all SMC racks. This version comes with an alignment training groove.
7/8" diameter aluminum bar for one of your first or top bars. The extra mass acts as a heat sink and the training groove helps keep the rope centered in your rack. Use only one top bar per rack.
The 7/8 inch top bar is designed to stay on your rack and virtually last forever. Has machined groove to keep the rope centered. Core drill out keeps this bar cool and lightweight. Use only one top bar per rack.
The shape and size of this carabiner makes it great for most uses, from connecting a belay device to your harness or as a connector at the end of a lanyard. The D-shape makes it one of the strongest and lightest locking carabiners Petzl makes. Perfectly suited for use with belay devices due to its symmetric shape on both ends of the carabiner. In addition, the D-shape has the highest strength-to-weight ratio of all Petzl carabiner designs. This carabiner comes with Petzl's Keylock system.
Available with manual locking (SCREW-LOCK) gate or auto-locking systems (BALL-LOCK, TRIACT-LOCK).
Certifications: CE EN 362, CE EN 12275, type K (K and B for M34 SL), UIAA
A CMC original design that has withstood the test of time, these Anchor Plates keep the carabiners, holding the different parts of your rescue system, from jamming together. The hardware becomes easier to see, making safety checks more accurate. It can also keep you from clipping a carabiner into the wrong loop of the anchor web, risking failures.
For most anchor systems, it makes an excellent collection point.
Besides serving as the point of distribution to any number of secure anchor points, rigging plates also serve the benefit of aligning the separate lines of a rigging system in distinct order, keeping multiple and various lines orderly. One tip when determining complementary gear to use with rigging plates; consider the versatility swivel pulleys can lend to the rigging system. They introduce rotational movement into the rigging lines running from the plate because the swivel pulley can rotate as needed to provide enhanced in-line ability to clear other components within the system.
ASAP Mobile fall-arrest device for rope.
With its unique locking system, the ASAP is a reference product in fall protection for workers at height. In normal use, the device moves freely along the rope without any manual intervention and accompanies the user in all his movements. In case of shock or sudden acceleration, the ASAP locks on the rope and stops the user. The ASAP may also be combined with an ASAP'SORBER energy absorbing lanyard to work at a distance from the rope and absorb fall forces.
Stops a fall, a slide or uncontrolled descent. For use on a lifeline (9mm to 13mm). Locks even if the device is grabbed during a fall. Works on vertical or angled rope. Moves up and down along the rope without manual intervention. Easy to install and remove at any point on the rope. May be used with an ASAP'SORBER energy absorbing lanyard to create the desired distance from the safety line.
Comes with a OK TRIACT-LOCK automatic locking carabiner
Materials: aluminum, stainless steel
Certifications: CE EN 353-2, CE EN 12841 type A, EAC
Weight: 370 g (295 g for ASAP and 75 g for OK TRIACT-LOCK)
The ASAP LOCK mobile fall arrester is designed to facilitate manipulations during rope ascents. In normal use, the device moves freely along the rope without any manual intervention and accompanies the user in all his movements. In case of shock or sudden movement, the fall arrester locks on the rope and stops the user.
The ASAP LOCK's integrated locking function allows the user to immobilize the device to reduce the length of a fall and can be used to keep tension on a line in high winds. The connection arm makes the system loss-resistant when passing intermediate anchors. The ASAP LOCK is used with an energy absorbing lanyard to work at a distance from the rope.
The ASAP LOCK provides constant fall protection and arrests falls, slides, and uncontrolled descents working on both vertical and angled rope setups and locks on the rope even if grabbed during the fall.
Materials: aluminum, stainless steel, nylon
Certifications: CE EN 353-2, CE EN 12841 type A, EAC
Weight: 425 g
Petzl's handled ascenders have been refined to provide greater comfort, efficiency, ease of use. The ergonomically shaped handle is over-molded with dual density grip for greater friction and better grip. The grip is wider at the bottom, providing better comfort for your pinkie fingers during use. The index finger indent has also been increased, offering greater efficiency when pulling on the ascender. The ergonomic trigger allows one-handed installation and removal. The two attachment points allow for different uses (e.g. self- belaying, hauling systems, etc.)
The geometry of the single piece aluminum frame ensures optimal handle orientation when the device is loaded and will maintain solid, comfortable performance for ascents of any length and the mono-frame construction eliminates weaknesses and keeps the ascender lightweight and durable for years of use.
The cam has been redesigned to minimize friction when sliding the ascender up the rope while the angled teeth provide secure grip in the worst of conditions (wet, icy, or muddy ropes).
Anodized frames are colour-coded for easy identification (except the tactical black versions). An added safety catch prevents the cam from opening too far, helping to keep the rope captured for added safety.
Materials: aluminum, stainless steel, plastic, rubber, nylon
Weight: 165 g
Rope compatibility: 8 to 13 mm
Certification(s): CE EN 567, CE EN 12841 type B, EAC, NFPA 1983 Technical Use
A lite alloy steel carabiner featuring double or triple action gates. Easily opened with one hand, but once released, the gate closes to a fully locked position. The carabiner gate and sleeve are stainless steel for problem-free operation. An offset inchD inch shape provides a smooth transfer of the Munter hitch when used as a belay and has ample volume to clip in large diameter ropes and over the rails of most litters.